Vietnam or Thailand ? Vote for the TOP Country of the Week !
Updated: July 9, 2025
When the two parts of the clutch are separated, as they are when the yarn breaks or runs slack, when it is exhausted, or when the cop reaches a predetermined length, the spindle stops; but when the two parts of the clutch are in contact, the small skew bevel wheel drives the clutch, the latter rotates the spindle, and the spindle in turn draws forward the yarn from the bobbin, and in conjunction with the rapidly moving yarn guide and the inner surface of the cone imparts in rapid succession new layers on the nose of the cop, and thus the formed layers of the latter increase the length proportionately to the amount of yarn drawn on, and the partially completed cop moves slowly away from its cup or cone until the desired length is obtained when the spindle is automatically stopped and the winding for that particular spindle ceases.
At night, when the house was still and all the rest asleep, Carew often came and stood before this panel, with a queer, hesitating look upon his hard, bold face; and stretching out his hand, would press upon the head of a cherub cut in the bevel edge.
After nearly an hour of this walk, trot and canter she was very rosy, and quite out of breath. Then she was put back into the limousine and driven swiftly home. And it was not until after her arrival that she had a moment entirely to herself, and the first opportunity of comparing her height with the tiny ink-line on the edge of the mirror's bevel.
The machine has also a bevel track very useful for picture frame molding, and a patent cap of great value for the cutters, and readily applied to any slotted head or common head. The wrenches that go with the machine, and the common malleable iron caps for the top cylinder, are shown in detail.
We hear it again from the lips that cannot lie: 'Did ye never read in the Scriptures, The Stone which the builders rejected, the same is become the headstone of the corner? And for the last time the venerable metaphor which has cheered so many ages appears in the words of that Apostle who was 'surnamed Cephas, which is by interpretation a stone': 'To whom coming as unto a living Stone, yea also as living stones are built up. As on some rocky site in Palestine, where a hundred generations in succession have made their fortresses, one may see stones with the bevel that tells of early Jewish masonry, and above them Roman work, and higher still masonry of crusading times, and above it the building of to-day; so we, each age in our turn, build on this great rock foundation, dwell safe there for our little lives, and are laid to peaceful rest in a sepulchre in the rock.
"Of course, to make such high speed for ordinary carriages possible, a perfect pavement became a sine qua non. We have secured this by the half-inch sheet of steel spread over a carefully laid surface of asphalt, with but little bevel; and though this might be slippery for horses' feet, it never seriously affects our wheels.
Each pupil is provided with the following tools: One coach-maker's vise, one 26-inch No. 6 cross-cut saw, one 12-inch back saw, one set of planes, one set of chisels, one set of auger-bits, one set of gimlet-bits, one ratchet-brace, one coach-maker's drawing-knife, one spoke-shave, one thumb-gauge, one try-square, one bevel, one hammer, and one mallet.
Heywood also invented a wheel for bringing staves to a bevel and taper, for the construction of barrels systematically. Mr. Heywood remained in town eight or ten years, when he moved to Claremont, N. H., where he died at the age of eighty years or more. He was thoroughly upright, but he had too many schemes for a successful business man. During my term with Mr.
Bevel off the ends of the last inside to allow the valve to enter easily. Make the valve. Bore the steam ports, and solder valve tube and cylinder together. Solder holding-down wing, W, to cylinder. Finish off the piston. Solder the bearings in their standards. Prepare shaft, crank disc, crank pin, and piston rod.
As the side of the hole nearest to the bottom corner should run obliquely to enable the tube to pass, work this out with the file held at an angle. Then bevel off the end to 45 degrees and pass the tube through again, bringing the bevel up against the bottom hole from the inside. If it is a trifle difficult to pass, bevel off the edge slightly on the inside to make a fairly easy driving fit.
Word Of The Day
Others Looking